TimberCare Porch & Floor

TimberCare Porch & Floor

Anti-slip stain for wood and concrete floors and decks

General Features:

• Allows wood to breathe
• High UV resistant
• Anti-slip features with micro particles
• Water repellent
• Lead-free
• Environmentally friendly
• Ready to use
• Interior and exterior use

Where To Use:
Interior: wooden and concrete floors indoors, stairs, handrails, balusters, etc;
Exterior: wooden and concrete decking, terraces, footpaths, ramps, courtyards, porches, steps, facades, handrails, balusters, etc.

Packaging Size:

• White Base 2,375 L
• Clear Base 2,34 L

Gloss: Satin

Type: Water-based

Application Method: Brush or roller
Number of Coats: 2 coats

Coverage (m²/L): 6-7 m² with 2 coats depending on wood type

Drying Time (at 20°C and 40-65% relative humidity):
Touch Dry: 4-6 hours
Recoat: 6 hours
Complete Dry: 24 hours

Product Data:
Solid Content (% weight): 26,7 ± 1
Viscosity (DIN4, 25°C): 45“ ± 2
Density (g/cm3): 1 ± 0,02
VOC (g/L): 62

Thinning:
Ready to use, does not require thinning. (At very high temperatures 5% drinking water may be added).

Surface Preparation:
Remove any dirt, oil and wood dust from the surface.

New Wood Surfaces:

• Sand the surface with sandpaper #80/120.
• Thoroughly clean the generated dust.

Old Uncoated Wood Surfaces:
Sand the weathered surface with sandpaper #80/120 or restore wood surface using HEMEL Deck
Restorer.

Coated Wood Surfaces:

• Do not apply the product directly on pre-coated surfaces.
• Remove the old paint/varnish from the surface completely with a sanding machine.
• Thoroughly clean the generated dust.

Application:

• The product is ready to use and does not require thinning. (At very high temperatures 5% drinking water may be added).
• Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
• Apply the product in 2 coats by a brush or roller without sanding between coats.
• Wait 6 hours between coats.
• Apply in the direction of wood grain to get a homogeneous look.
• The treated surface may be stepped on 24 hours.

Maintenance (when the same product had been used before):

• Do not apply the product directly on pre-coated surfaces.
• Remove the old paint from the surface completely with a sanding machine.
• Thoroughly clean the generated dust.
• Repeat same process as described in “Application”.
• Inspect annually and maintain as required.

Instructions:

• FOR EXTERIOR USE ONLY.
• Keep product closed when not in use.
• The general application temperature of the product is between 15oC to 25oC at a relative humidity range of 40-65%.
• The moisture content of the wood should be max. 20%.
• Do not apply the product under direct sunlight or rain.
• Do not apply linseed oil, basecoat/primer, yacht varnish before or after TIMBERCARE PORCH & FLOOR applied surfaces.
• The product should be protected from freezing and stored at temperatures between 5°C to 35°C.
• Painting tools should be cleaned with soap and plenty of warm water after application.

Safety Precautions:

• USE WITH ADEQUATE VENTILATION.
• KEEP OUT OF REACH OF CHILDREN.
• Do not transfer contents to other containers for storage.
• Do not use empty cans for other purposes.
• To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
• Avoid contact with eyes and skin.
• Wash hands after using.
• FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists.
• If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
• Dispose of contents/cans in accordance with national regulations.
• Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.

Certificates: EN71-3 Toy Safety Certificate

Shelf Life (5-35°C): 3 years for unopened can